PCI 530 Series
ImageStream's PCI 530 series network cards are low-cost PCI 2.1 compliant network adapters that support multiport T1/E1/J1 or DS3/E3 connectivity for WAN and Internet routing applications. The software included with ImageStream's router distribution is used to configure each of the soft-set interfaces.
530 series WAN adapters support full or fractional line speeds independently for each port. The T1/E1/J1 cards also support DS0 multiplexing, as well as drop-and-insert with the 2 and 4 port versions. The DS3/E3 cards support full or fractional line speeds configurable in DS1 (1.5 Mbps) increments.
The 530 series T1/E1/J1 cards use a fully integrated design based on the PMC Comet and Altera chipsets. The 530 series DS3/E3 cards use the high-performance Intel 21143 chipset that supports duplex E3 speeds up to 34 Mbps per port and DS3 speeds up to 45 Mbps per port, with a maximum aggregate throughput of 180 Mbps.
The 530 series hardware supports bisync and SDLC/HDLC protocols with a low-latency PCI interface that can burst into host memory at speeds up to 256 MBps. The 530 series cards provide a PCI bus interface that is compatible with 3.3 and 5 volt signaling systems. The T1/E1/J1 cards provide a 32-bit 33 MHz PCI bus interface, and the DS3/E3 cards provide a 32-bit 33/66 MHz PCI bus interface.
The PCI 531-DE and 532-DE support fractional and full DS3 circuits. There is no adopted industry standard for encoding fractional E3 circuits, and so the 530 series DS3/E3 cards only support full E3 operation. To provide fractional E3 bandwidth services over a full E3 circuit, most carriers and ISPs will provision a full E3 circuit and use bandwidth limiting to provide the same bandwidth as a fractional circuit.
|
| |
Performance:
- Low-latency PCI bus master
- T1/E1/J1: 32-bit 33 MHz PCI
- DS3/E3: 32-bit 33/66 MHz PCI
- T1/E1/J1: Up to 4 ports, 16 Mbps aggregate throughput
- DS3/E3: Up to 2 ports, 180 Mbps aggregate throughput
Technical Highlights:
- Up to 4 full duplex T1/E1/J1 ports
- Up to 2 full duplex DS3/E3 ports
- PCI 2.1 compliant
- Universal 3.3 and 5 V signaling
- Short PCI form factor
- MTBF of at least 100,000 hours
Interface Options:
- Single, dual or quad T1/E1/J1 ports
- Single or dual DS3/E3 ports
Environmental Requirements:
- Operating temperature –5 to 55 degrees C (23 to 131 degrees F)
- Relative humidity 5 to 90% (non-condensing)
Power Requirements:
- 500 milliamps @ 5 volts (max)
T1 Interface Specifications:
- D4 (SF) and ESF framing
- B8ZS and AMI line coding
- ANSI T1.403, AT&T 54016 and 62411 compliant
- Test and loopback features including master & slave clocking
- RJ48 connectors
|
|
E1 Interface Specifications:
- AMI and HDB3 line coding
- ITU G.703 via 120 ohm balanced RJ48
- ITU G.703 via 75 ohm unbalanced coaxial (requires balun)
- G.704, G.706, G.962
- Test and loopback features including master & slave clocking
DS3 Interface Specifications:
E3 Interface Specifications:
- ITU G.703 (75 ohm)
- ITU G.751
Certification:
- FCC Part 15 Class A
- FCC Part 68
- UL 1950
- UL Safety
- CISPR22
- CS003, CS03
- DOC Canada
- EN 50082-1, EN 55022, EN 41003
- PICMG PCI 2.1
|
Model Numbers and Interface Configurations:
- 531-TEJ - One T1/E1/J1 CSU/DSU interface
- 532-TEJ - Two T1/E1/J1 CSU/DSU interfaces
- 534-TEJ - Four T1/E1/J1 CSU/DSU interfaces
- 531-DE - One DS3/E3 CSU/DSU interface
- 532-DE - Two DS3/E3 CSU/DSU interfaces
Related Products:
- TAP-TE-RJ48 - Passive T1/E1 monitoring tap
- TAP-DE-6BNC - Passive DS3/E3 monitoring tap
|
|
|
|
|
Lab Test
|
|
|
Lab Test
of the
Rebel
Router
|
|
|
|
|
|
CompactPCI
Systems
Publishes
Article
on Inetics
(formerly SAND)
|
|
|
|
|
|
